Suction and compression process The suction and compression of the injection pump is accomplished by the plunger reciprocating within the plunger sleeve. When the plunger is in the lower position, the two oil holes in the plunger sleeve are opened. The inner cavity of the plunger sleeve is communicated with the oil passage in the pump body, and the fuel is rapidly filled in the oil chamber. The plunger rises as the cam hits the roller of the roller body. Move upward from the beginning of the plunger until the oil hole is blocked by the upper end of the plunger. During this time, due to the movement of the plunger, the fuel is squeezed out of the oil chamber and into the oil gallery. So this lift is called pre-stroke. When the plunger block the oil hole, it began to pressure process. Plunger up, oil chamber pressure rose sharply. When the pressure exceeds the spring force of the oil valve and the upper oil pressure, the oil valve is opened and the oil is pushed into the oil pipe by the oil pressure.
The time when the oil inlet hole on the plunger sleeve is completely blocked by the upper end surface of the plunger is referred to as the starting point of the theoretical oil supply. Continue to move up the plunger, the fuel has been continued, the pressure process continues until the helical bevel on the plunger to open the plunger sleeve back to the oil hole so far, when the hole is opened, high pressure oil from the oil chamber by The longitudinal groove on the plunger and the oil return hole in the plunger sleeve return to the oil passage in the pump body. At this point the plunger sleeve oil chamber pressure rapidly reduced, the oil valve in the spring and high pressure tubing back to the valve seat, the injector immediately stop injection. At this point although the plunger is still up, but the oil supply has been terminated. The plunger oil return hole is opened by the hypotenuse of the plunger is called the theoretical end of the oil supply. In the plunger up the entire process, only the middle of the stroke is the process of pressure, this stroke is called the effective stroke of the plunger.
Fuel Level Adjustment To meet the diesel load requirements, fuel pump delivery must be capable of being regulated from maximum fuel supply (full load) to zero fueling (parking). Fuel supply regulation is through the gear rod, rotating sleeve so that all the fuel injection pump plunger rotation to achieve. When the plunger rotation, the fuel supply start time unchanged, and the end of the oil supply, due to the hypotenuse of the plunger sleeve back to the hole position change changed. With the different angles of rotation of the plunger, the effective stroke of the plunger is also different, so the amount of fuel supply also changes.
The greater the angle the plunger does not rotate the oil supply 1, the greater the distance between the upper end of the plunger and the hypotenuse of opening the oil return hole of the plunger sleeve, the greater the oil supply. If the plunger rotation angle is greater Small, the oil cut started earlier, the fuel supply is also smaller. When the diesel engine must be off when the oil, to this end, the longitudinal groove on the plunger can be turned directly to the plunger sleeve on the back hole. At this point, throughout the plunger stroke, the fuel in the plunger sleeve has been through the longitudinal groove, back to the oil hole back to the oil hole, there is no pressure process, so the fuel supply is equal to zero. When the plunger rotation, the use of change the end of the moment to adjust the amount of fuel supply, this method is called the oil endpoint adjustment method.
Fuel pump oil supply to meet the needs of diesel engines in a variety of conditions, that is, when the load increases for a large amount of fuel: load hour reduced fuel supply. At the same time also ensure that the fuel supply to each cylinder should be equal. According to the requirements of the diesel engine, the oil pump must ensure the same starting time of each cylinder, that is, the advance angle of each cylinder should be the same, and the same duration of oil supply should be guaranteed. Oil phenomenon. Depending on the type of combustion chamber and the method of forming the mixture, the pump must provide sufficient fuel to the injector to ensure good atomization quality.
More Search Keywords: Oil Pump
Spunbond Nonwoven Production Line
The polyester PET non-woven production line is used for the production of non-woven fabrics such as polypropylene spinning, web forming, and hot rolling reinforcement. Using polypropylene as the main raw material, supplemented by color masterbatch, anti-oxidation, anti-pilling, flame retardant and other auxiliary agents, it produces PP spunbond hot-rolled non-woven fabrics with different colors, properties and uses, and polyester spunbond and hot-rolled non-woven fabrics. It has the excellent characteristics of high strength, low shrinkage, heat resistance, good stability, breathable waterproof, flame retardant, acid and alkali resistance, moth-proof, non-toxic and anti-ultraviolet.
Spunbonded non-woven fabric production line, non-woven fabric production line, non-woven fabric production machinery and equipment, non-woven fabric making machine
Changzhou Puyisen Machinery Technology Co., Ltd. , https://www.pysmachine.com